So, I purchased the FMP with the understanding that a 3 year lease at 25000kms a year it was a good deal at the $1000.00 bucks for the term. Logic was that at least one brake job on both front and back, oil changes, wiper blades, etc, etc. Now with 36000 kms on it, I recently had the front brake TSB done. When I picked up the Flex the young lady at the desk say's 'you know that there's one for the backs as well right' and winks at me! I said that yes I did know that. So here I am waiting out the back brakes until they grind or whatever, and will get that TSB done.
This page is not a piece of advice to remove FMP by Ford Motor Company from your PC, nor are we saying that FMP by Ford Motor Company is not a good software application. This page simply contains detailed instructions on how to remove FMP supposing you want to. May 08, 2012 How can i get as built data for 2012 fusion - Answered by a verified Ford Mechanic We use cookies to give you the best possible experience on our website. By continuing to use this site you consent to the use of cookies on your device as described in our cookie policy unless you have disabled them.
Thus, the $1000.00 I spent on the FMP turned out to be a waste in retrospect!!!
Ford, Lincoln, Mercury, Ford Rotunda, Ford dealer, service tools, special tools, specialty tools, workshop equipment, essential special service tools, DES, dealer. Feb 18, 2018 How to Reprogram a used Ford PCM With FJDS and a J2534 device. J2534 Reflashing with Ford FMP - Duration: 11:08. NASTFdotOrg 26,302 views. Tool Hut USA 9,371 views.
Rant concluded....
Brownie
It’s aimed to help how to reprogram/reflash Ford PCM via IDS software using scanners like VCM2 or VXDIAG VCX NANO for Ford. Also, solutions of Error Code:11.0x0 851082 will be shared here by other users.
Model:
2006 Ford Fusion
Error message:
'The operation cannot begin because the PCM failed to complete a service procedure. Perform PMI on the PCM to resolve the issue.'
Possible scanners working with:
Customer solution:
Turn off your firewall
Customer B:
Uninstall fmp and reinstall it. I have had this happen before. I have had some new pcm be un programmable. And just for reference. Fmp doesn't like Google. Use 32 bit processor as well. I had to slow my computer down from 64-32 because fmp would not work correctly with 64. Good luck.
Customer C:
If you are checking PCM for up-dates, Ford will advise on 6.0L powertrain if there is a reflash avail for TCM, FICM or PCM, if it states there is no update then all three modules are at latest level, no action required, I am aware it states to remove FICM relay prior to reflash FICM, this is a carryover note from when we used PDS or WDS to reflash the FICM, if you are using IDS with VMM interface its not required to remove the FICM relay, I have reflashed over 1000 of them this way over the last 7 years, as always make sure the battery stays in the sweet spot @ 13.5 volts, make sure your laptop has sufficient power, I always plug in, make sure cables to veh and laptop are safe from accidental disconnect, Good luck!
Customer D:
If you try to VCM2 genuine or clone to make reprogaming well you need IDS V98.01 or higher. It would be good to check if during initiation programming interface output 18,5V on pin 13 in OBD connector.
How to reprogram PCM via IDS software:
Main procedure: Step 1: Install a new PCM Step 2: Reprogram PCM
Install VMware and well setup IDS software follow the video/pdf guide (see attachment below)
Select “Start New Session”
The SAE J2534 pass-thru device cables must not interfere the safe operation of the vehicle. Secure all cables away from the vehicle pedals.
Turn ignition to ON
Apply Neutral/Park gear position
Verify vehicle information
Select “Module programming”
Again verify vehicle information and confirm
Check if the displayed VIN is correct, if yes, hit Yes to continue
Follow the system prompt to install a new module in vehicle
Please read the following information carefully.
NOTE: Do not start a reprogramming session with a low battery in the vehicle and/or programming tool.
The fuel pump and the engine cooling fan(s) may run during the following procedure.
If you are programming a 6.0L diesel, the FICM replay must be removed before programming.
Turn ignition to ON position
Downloading data and reprogramming PCM in progress
Turn ignition to OFF
Turn ignition to ON
Calibration has been loaded and checked.
If you programmed a 6.0L diesel please reinstall the FICOM relay.